ISO/TS TECHNICAL SPECIFICATION 13399-311 First edition 2016-03-01 Cutting tool data representation and exchange - Part 311: Creation and exchange of 3D models - Solid reamers Repreésentation et échange des données relatives aux outils coupants Partie 311: Création et échange des modeles 3D - Alésoirs a aretes de coupe non amovibles Reference number IS0/TS 13399-311:2016(E) ISO International Organization for Standardization @ IS0 2016 HEJIANG INST OF STANDARDIZATION C1 5956617 ed without license from IHS IS0/TS 13399-311:2016(E) COPYRIGHTPROTECTEDDOCUMENT IS02016,PublishedinSwitzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below or ISO's member body in the country of the requester. IsOcopyrightoffice Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org Intenationaibr PrganizationforStandardization icensee-ZHEJIANG INST OF STANDARDIZoISQ s.6 - All rights reserved etworking permitted without license from IHS IS0/TS 13399-311:2016(E) Contents Page Foreword ..V Introduction. ..vii 1 Scope. 2 Normative references 3 Starting elements, coordinate systems, planes 2 3.1 General. 3.2 Reference system.. 3.3 Primary coordinate system and mounting coordinate system .2 3.4 Coordinate system at the cutting part 3.5 Planes 4 3.6 Cutting reference point ..5 4 Design of the model ..5 4.1 General ..5 4.2 Necessary properties for the connection interface feature. ..6 5 Cylindrical reamer .6 5.1 General. .6 5.2 Necessary properties .7 5.3 Geometry of the non-cutting part including the connection. ..7 5.4 Geometry of the cutting part. ..8 5.5 Complete cylindrical reamer.. 6 Tapered reamer .9 6.1 General .9 6.2 Necessary properties .10 6.3 Geometry of the non-cutting part including the connection. ..10 6.4 Geometry of the cutting part. 10 6.5 Complete tapered reamer .11 ..11 7 Stepped reamer 7.1 General. .11 7.2 Necessary properties. .12 7.3 Geometry of the non-cuttingpart includingthe connection. ..13 7.4 Geometry of the cutting part. ..13 7.5 Complete stepped reamer. ..14 8 Bell-style reamer ..14 8.1 General ..14 8.2 Necessary properties.. .15 8.3 Geometry of the non-cutting part including the connection. ..16 8.4 Geometry of the cutting part. ..16 8.5 Complete bell-style reamer ..17 9 Shell reamer ..17 9.1 General. .17 9.2 Necessary properties. .18 9.3 Geometry of the non-cutting part including the connection. .18 9.4 Geometry of the cutting part. .19 9.5 Complete shell reamer. .20 10 Design of details. 21 10.1 Basics for modelling .21 10.2 Contact/clamping surfaces - ( Orientation .21 10.3 Chamfers and roundings. .21 11 Attributes of surfaces - Visualization of the model features. .21 iii ISee=ZHEJIANG INST OF STANDARDIZATION C1 5956617 vided by IHS under license with ISC ed without license from IHS Not for Resale, 2016/4/26 02:47:28